﻿[V5.0.1.22]
1. Fixed. Rssi issue when close to connected AP

[V5.0.1.21]
1. Fixed. Scan no ap during s3/s4/s5 or radio off/on

[V5.0.1.20]
1. Fixed Disconnect, Scan no ap issue during chariot througput
2. Change Endpoint from 8 to 6.
3. Remove timer from packet complete to callback event. call directly 
4. Update Firmware for MT7610U

[V5.0.1.19]
1. Fixed. Clear Null frame bulk flag in correct place
2. Fixed. Data packaet has extra bytes cause bulkout issue after few hrs.

[V5.0.1.18]
[Interface: USB] [OS: All] [IC: 7612] [WCNCR: WCNAE00084743] [BSOD: N/A] [Customer: Edimax]
1.) [Bug][EDIMAX_EW-7722UAC V1.0A] 2pcs TX TP can't reach 866Mbps (2/100)
    [Solution] Call FW to do TX Shaping after both Load CR and Power on full calibration.
	
[V5.0.1.17]
[Interface: All] [OS: All] [IC: 7662] [WCNCR: WCNCR00013362] [BSOD: N/A] [Customer: N/A]
1.) [Feature] MT7662 series WDOG setting change notice
     [Description] http://teams.mediatek.inc/WCP/WCN/Combo/MT7662/MT7600/09_Validation/03_CSD/BBP_CR_Update/MT7662E5_BBP_CR_20140922.xls
     [Solution] Update 0x212c by BBP CR release MT7662E5_BBP_CR_20140922.xls
	 
[V5.0.1.16]
[Interface: All] [OS: All] [IC: 7610] [WCNCR: N/A] [BSOD: N/A] [Customer: N/A]
1.) [Feature] Enables BBP Watchdog with 13ms threshold WDOG setting
    [Description] http://teams.mediatek.inc/sites/WHN/MT7650/MT7650_E2/60_E6/Register Programming Sequence/MT7650_MT7662_WDOG_Usage.pptx
    [Solution] update 0x212C by BBP CR release: MT7650E6_BBP_CR_20140922.xls.
	
[V5.0.1.15]
1. Fixed . Null frame size is incorrect. added 4 byte padding two times
2. Added more Driver log

[V5.0.1.14]
[MT7610U][MT7612U]
1. [Bug] EDCCA Test Fail
   [Solution] Add SW EDCCA detection, turn off PA and preventing switching channel
2. [Bug] EDCCA Test Fail at ADT table. Tx will over 5ms when ESG is generating interference signal
   [Solution] 1.Prevent SW timer function interval is too far from 1sec
              2. prevent bulkout fail to cause wkan reset
              3.Prevent packet command stuck and cause wlan reset.
              4. Fix dynamic VGA setting is not correct if EDCCA enabled
3. [Feature] Enhancement for EDCCA Test. EDCCASGDetected flag may be incorrect due to link down during EDCCA test 
   [Solution] Turn off PAPE if ED signal is detected event link down
4. [Bug] DFS Fail. 
   [Solution]1. Do LC Calibration Once when adapter is initial. Restore the LC Value for each switch channel
             2. set TxRTY count as 1 when receiving switch channel announcement
             3. Do TSSI adjustment only When linkup
              
5. [Feature] 7612 FW update. 20190918
   [Modification] 1. Enable IBI watch dog (timeout from 10ms to 13 ms)
                  2. WOW modified for TV SQA
		  3. LC-Calibration backup/restore support

[V5.0.1.13]
[MT7612U]
1.  [Feature][MT7612] WIFI MAC Initial CR Update - 140821
    [Description] The update is to fixed an IOT issue found in MT7612 and MT7628 RDG test.
    [Solution] Update MacInitRegTable7662 by http://teams.mediatek.inc/WCP/WCN/Combo/MT7662/MT7600/09_Validation/Initial%20CR/WIFI_MAC_PBF_SEC/MT7662_E5_CR_setting_140821.xlsx
	
[V5.0.1.12]
[MT7612U][MT7610U]
1. Support set and query Country Region 
2. Support DFS

[V5.0.1.11]
[MT7612U][MT7610U]
1. Some code does not include VHT for Phy is A Band capable
   Use macro as each PHY combination ex. IS_PHY_SUPPORT_5G_ONLY
   Remove PHY_11A check and only use RadarChannelCheck for DFS
   
[V5.0.1.10]
[MT7610U][MT7612U]
1. Support EDCCA
 
[V5.0.1.09]
[MT7612U]
1. Fixed Scan no AP after sleep long time
2. Added Following PID&VID
   MT7610 => ASUS PIDA711_VID7392
   MT7610 => ASUS PIDB711_VID7392
   MT7610 => Comcast PID293C_VID5702
   MT7612 => ASUS PID180B_VID0B05
	
[V5.0.1.08]
[MT7610U]
1. Fixed. Disconnect within 10 min while througput performance

[V5.0.1.07]
[MT7612U]
1. Fixed Scan no AP after Radio off/on and sleep/wakeup

[V5.0.1.06]
[MT7610U]
1. Fixed Ping response time is over 1000ms when Ac AP configured with 20/40/80 BW auto

[V5.0.1.05]
[MT7610U]
1. Bug : Low throughtput with broadcom AP
   Solution : Do not turn on Tx burst if ap is vbroadcom ap.
2. Add Netgear A6210 PID & VID : USB\VID_0846&PID_9053
   
[V5.0.1.04]
[MT7612U]
1. Bug :		Manual Channel setting by eFuse fail.
   Solution :	Update NICReadEEPROMParameters about the manual channel of MT7612-EEPROM Content v0 1_04_guideline.pdf
   
[V5.0.1.03]
1. Add calibration for MT7610U
2. MAC CR update for optimize Tx Switch Timing for 20/40/80M
3. Change copyRight info from Ralink to MediaTek Inc.
4. Fix Scan no AP Issue for MT7612U
5. Fix Scan no AP issue for MT7610U

[V5.0.1.02]
1. Fixed HW PBC issue

[V5.0.1.01]
1. Implement SoftAP features
2. Added OID to inform Driver terminate event to UI,SDK
 
[V5.0.1.0]
1. MP release for MT7612U

[V5.0.0.09]
1. Update Firmware
2. Update Patch_ROM Firmware

[V5.0.0.08]
1. Fixed Scan no AP Issue
2. Fixed connect g mode then unable to connect A mode

[V5.0.0.07]
1. Support SoftAP feature
2. Support MT7601
3. Update Firmware for MT7601.  to fix after reboot Device spead is full speed instead of high speed.

[V5.0.0.06]
1. Add LED Mode 2 for 7612U DNI. Expand LED Status with LED_CONNECTING and LED_CONNECTED.

[V5.0.0.05]
1.Sync With Windows driver 5.1.8.122
2.Update patch FW for MT7612U

[V5.0.0.04]
1. sync with windows driver 5.1.8.79
2. Fixed PerformRxDCOCCalibration7662 function

[V5.0.0.03]
1. sync with windows driver 5.1.8.53
2. Update FW
3. Support 2.4G 256QAM(BW20/40) at MT7612U STA. Add new param in Registry, "2G256QAM"
4. Modify protection pate from OFDM 24M to 36M in the last condiction(sync to PCIe code)
5. Revise download FW packet size from 14k to 8k to avoud redownload fw fail.
6. New define 7612_E4 to check if it is E4 card. 

[V5.0.0.02]
 1.sync with windows driver 5.1.8.29

[V5.0.0.01]
 1.Support 7612U
 2.sync with windows driver 5.0.8.5133
 
 
[V4.2.9.10]
 1.Fixed : Mac STA connects to Ad-hoc on 2.4G The data rate will show only 11Mbps

[V4.2.9.9]
 1. Add checking for spinlock to avoid kernel panic.

[V4.2.9.8]
 1. Remove log print of RTMPXmitLinkSpeed.

[V4.2.9.7]
 1. Implement the feature of the Network Utility statistic.

[V4.2.9.6]
 1. Fixed the scutum cannot connect by bssid in 10.9.

[V4.2.9.5]
 1. Fixed WCNCR00005491. throughput of Tx does not reach standard in legacy mode.
 2. Change copyright info

[V4.2.9.4]
 1. Fixed the free wrong size memory in MlmeFreeMemoryHandler(), it will cause kernel panic in 10.9.

[V4.2.9.3]
 1. Remove the patch that switchband(BW 20) in scan, Due to it is only a patch not the root cause.

[V4.2.9.2]
 1. fixed WCNCR00005490. Radio Off -> Radio on in Raui then nscan no AP
 2. fixed WCNCR00005496. Overnight fail. scan no AP
 3. fixed WCNCR00005485. IOT issue with realtek 2*2 AP. unable to connect with WPA/WPA2PSK 5Ghz.
 4. fixed WCNCR00005473. Sleep -> Resume Scan no AP


[V4.2.9.1]
 1. fixed the hidden AP connect issue by sending seconde probe req
 2. switchband(BW 20) in scan, to prevent that sometimes sta cannot recieve probe response from hidden AP when scanning.

[V4.2.9.0]
 1. Formal Release
 2. Implement Throughput issue
  
[V4.2.8.27]
1.) For MT7610 fixed the issue that Cold/Warm boot cannot reconize the NIC by add IOMatchCategoey property in plist file.

[V4.2.8.26]

1.) Fixed 
WCNCR00004812.[MT7610U][sta][wifi-function][MAC]:sta ??N?AP (tkip),??N ?AP (aes)sta????N AP ?BA.

[V4.2.8.25]

1.) Add case RT_OID_QUERY_HW_ARCHITECTURE_VERSION for OID query to determine if the chip is 6x9x.
To fix UI get wrong tx rx rate(the transmit setting is different if the chip is 6x9x).



[V4.2.8.24]

1.) Add new MT7610U PID/VID PID:17D1,VID:0B05  for ASUS.



[V4.2.8.23]

1.) Set Led Off after sleep.

2.) Set Led bling when hwpbc is running.



[V4.2.8.22]

1.) insert new field(ULONG   Rsv;// RF Bank Number) into the RT_802_11_HARDWARE_REGISTER
	// structure for query/set hardware register - MAC, BBP, RF register
	
typedef struct _RT_802_11_HARDWARE_REGISTER 
{
		
ULONG   HardwareType;       // 0:MAC, 1:BBP, 2:RF register, 3:EEPROM
		
ULONG   Offset;             // Q/S register offset addr
		
ULONG   Data;               // R/W data buffer
		
ULONG   Rsv;				// RF Bank Number
	
} RT_802_11_HARDWARE_REGISTER, *PRT_802_11_HARDWARE_REGISTER;


2.) Add to query and set RF register settings



[V4.2.8.21]

1.) Modify the MAX_LEN_OF_BSS_TABLE from 64 to 128, sync to windows, for [WCNCR00004857] which cannot find the AP in the sitesurvey page.



[V4.2.8.20]

1.) Add new MT7610U PID/VID PID:AB31,VID:2019  for PCI(PLANEX COMMUNICATIONS INC).

[V4.2.8.19]
1.) Set Led in MlmeRadiooff(), it fixed reload firmware after wake up fail .
2.) Add compile source file for build setting of non-supplicant build.

2.) Remove loadfirmware in radio on(for not 6x9x). Move it to setPowerState() for wake up from sleep.



[V4.2.8.18]

1.) Reload firmware after wake up from sleep. Fixed bulkout command packet blocked after sleep and caused reload firmware failed. 

2.) Add the value check to prevent access to null pointer in getTargetAndMethodForIndex().

3.) Fixed potential unreleased spinlock in RTUSBVendorRequest().



[V4.2.8.17]

1.) Modify the mlmebulkout mechanism to only bulk out one packet at a time, after the previous one is completed then we bulk out the next one.(Paul Wu)

2.) Remove some spin locks which has not been used. 

3.) Add that if the adapter is 6x9x we don't write the USB class and subclass value(0x0206) in eFuse/EEPROM. Because the offset is not the same and no such a offset in MT7610U.

4.) Restore NICloadfirmware in MlmeRadioOn if the adapter is not 6x9x.



[V4.2.8.16]
1.) Add RTMPSetLEDbyStatus6x9x Function for 6X9X Led control, sync LED control from windows.

[V4.2.8.15]
1.) Sync MlmeRadioOn and MlmeRadioOff to Windows. It fixed Scan no AP after switch Radio off and then switch radio on.
2.) Temporarily remove set LED in MlmeRadioOn/MlmeRadioOff. It might cause Scan no AP after (S4).
3.) Rename PerformPowerUpCalibration to PowerOnFullCalibration (sync to windows)
4.) Sync PowerOnFullCalibration to Windows with enable RF. It fixed Scan no AP after wake from sleep (S4).

[V4.2.8.14]
1.) Correct check in error in mlme dataoutpipe[1] => dataoutpipe[2]

[V4.2.8.13]
1.) Sync Rt6x9x.cpp functions from XP
2.) Correct the parameter in ScanNextChannel() when adding ExtHtIE.
3.) Separate the dataoutpipe to 3 pipes 0: data 1: nullframe, mlmepacket 2: pktcmd.
4.) Remove delay 1500 in TXWI()(work around in 4.2.8.8).
5.) Only send one probe req in one channel when scan to avoid scan no AP.

[V4.2.8.12]
1.) Add table "LED.h" and "MT7650_tables.h".
2.) Fixed the parameters of switchband might be invalid such as channel = 0 or Use CentralChannel in BW_20.
3.) Fixed before end of scan in "ScanNextChannel()" we need to restore the current BW.
4.) Fixed the NullPacket with no header in only set the "fRTUSB_BULK_OUT_DATA_NULL" flag.
5.) Temporary set BW to 20 in "MlmeJoinReqAction" to patch that BW is always 80.
6.) Swap the sequence of "WscStop()" and "RTMPReleaseAllTimers()" in "MlmeHalt()" to avod cancel timer failed due to release timer before cancel timer.	
7.) Sync from XP, not to adjust TxPower in "STAMlmePeriodicExec()". Use it before calling periodicexec.
8.) With all logs been turned off, *Scan no AP* still happens in MT7610u.

[V4.2.8.11]
1.) Ported switch channel offload.
2.) Fixed pktcmd set timer fail.
3.) Update FW7650.h FW7601.h PowerTable.h MT7650E2_tables.h

[V4.2.8.10]
1.) Recover the action of posting message to supplicant in ioctl_supplicant.cpp, which had been mod in 4.2.8.1. Without this action may cause kernel panic Also recover some other actions that might affect

[V4.2.8.9]
1.) Remove the RT2xxx(RT2770/RT2870/RT2070) PID&VID form plist file
2.) For the workaround solution un-stable connected AP issue, change to delay 1.5ms without using the debug messages method

[V4.2.8.8]
1.) Sync XP driver form V5.0.6.1 to V5.0.8.0 (Not Include TSSI)
2.) Workaround Solution: Add the debug message to avoid the un-stable connected AP issue for MT7610u

[V4.2.8.7]
1.) Fix the MT7610u sometimes unconnected to BW 80Mbps issue.
2.) Fix command packet complete take long time issue. 
3.) Add FW SwitchChannel Offload, control by registry "SwitchChannelOffloadEnable" 


[V4.2.8.6]
1. Modify READ_RXWI_KEY_IDX for READ_RXINFO_MY_BSS error
2. For AsicUpdateProtect(), Update VhtProtect command
3. Improve the MT7610 TP. about 5G TX 150Mbps and RX 165Mbps
4. Patch for turn off TxBurst solution (Broadcom Cisco AP TP Issue)

[V4.2.8.5]
1. Updated RegTransmitSetting for TransmitSetting value (MT7610u/MT7610u)
2. Modify Debug method and add some debug messages
3. Fix Un-connected to 5G AP

[V4.2.8.4]
1.) For MT7610u, change the default phy mode vale to PHY_11VHT 
2.) Remove the MlmeRadioOff()/MlmeRadioOn(), and avoid reloading firmware 2 times
3.) Update IS_RT_NEW_DUAL_BAND_NIC(), let it support VHT chip
4.) Fix Un-scannig 5G AP issue

[V4.2.8.03]
1.) Fix the built errors that if the DBGPRINT is enabled
2.) Add Trace macro to print log

[V4.2.8.02]
1.) Connected to AP unstable issue (Rx MlmeQueueFull Error => Scan No AP)

[V4.2.8.01]
1.) Un-connect to AP issue (MT7601u/MT7610u)
2.) Mark unused variable.
3.) Reduce the warnings in built.
4.) Avoid the kernel panic for the pipeOutMDPs writed action of RTUSBBulkOutPktCmd()
5.) Add tables folder
6.) Add vht.cpp, vht.h, oid_rt6x9x.cpp, oid_rt6x9x.h, PktCmdRspEvt.cpp, PktCmdRspEvt.h, rt6x9x.cpp, rt6x9x.h

[V4.2.8.0]
1.) Support RT6X9X Chip (MT7601/MT7610)
2.) Sync to XP driver V5.0.3.2
3.) Sync to XP driver V5.0.6.0
	
[V4.2.7.1]
	1. New Add SiteCom VID_0DF6/PID_006E

[V4.2.7.0] 2012-10-18
	1. For RT3573: Disable HW_GPIO checking Radio On/Off
	2. For RT3573: Set VCO to middle
	3. New Add WNC VID_13B1/PID_003B
	
[V.4.2.6.0]
	1. 5G band canﾡﾦt scan AP after radio on/off.

[V.4.2.5.0]
	1. Re-modify 4.2.4.0.
	
[V.4.2.4.0]
	1. Changed Sitecomﾡﾦs RT3573 from 3x3 to 2x3.

[V.4.2.3.0]
	1. Fixed 5370G PPAD of Aux Antenna problem.

[V.4.2.2.0]
	1.	Fixed WEP 128 bit connection problem.
	2.	Enhanced auto co-work for 32/64 bit driver with 32/64bit UI.

[V.4.2.1.0]
	1.	32Bits Driver supported 64Bits Preferecne Panel UI..

[V.4.2.0.0]
	1.	Tuned scan time.

[V.4.1.5.0]
1.	Remove some setting in message function.

[V.4.1.5.0]
1.	Remove some setting in message function.

[V.4.1.4.0]
1.	Fixed WPA2-PSK/AES/TKIP connection problem on MAC OS 10.4.

[V.4.1.3.0]
1.	Fixed crash caused by spin lock deadlock.
2.	Fixed remove key too late when connect to WPA2-PSK/AES AP.

[V.4.1.2.0]
1.	Fixed RT3572 with HW PBCﾡﾦs GPIO problem. Register wrote wrong value.

[V.4.1.1.0]
1.	Fixed crashed problem when setting WDS type in mbuf.

[V.4.1.0.0]
1.	Supported RT5370.

[V.4.1.0.0]
1.	Supported RT3573.

[V.4.0.0.0]
1.	Supported SoftAp.

[V.3.0.3.0]
1.	Fixed WPA-PSK/WPA2-PSK Handshake function fro group key.
2.	Fixed Scutum canﾡﾦt connect when reboot.

[V.3.0.2.0]
1.	Fixed WPS LED MODE 8 when turn off Radio.
2.	Fixed group key hasdshake when rekey problem of TKIP.

[V.3.0.1.0]
1. Added VCO calibration.

	
[V 1.1.1.0] 2008-06-02
	1. Sync with VSS
	2. Resolved connection problem with DIR-300. Changed location of preparing IE of WPA-PSK/WPA2-PSK.

[V 1.0.0.0] 2007-03-29
	for intel MBP, remove unnecessary SimpleLocks
	release verison

[V 1.0.0.0] - RC1
	first release version

[V 0.0.1.e3]
	seems solve the sleep and wakeup panic issue.
	solve RT2890 on MacBookPro driver not release issue.
		return kIOReturnSuccess for message(kIOMessageServiceIsTerminated, ...)

[V 0.0.1.e2]
	longer the sleep time (to 100ms)for MlmeRadioON();

[V 0.0.1.e1]
	do not indicate connect for WPA-NONE in RTMPWPAAddKeyProc

[V 0.0.1.d9]
	sync with windows v1.0.2.0

[V 0.0.1.d8]
	fix sleep and wake connection

[V 0.0.1.d7]
	fix WPA-TKIP, AdHoc Beacon TxWI endian
	set init parameters


[V 0.0.1.d6]
[V 0.0.1.d5]
	sync to Windows - v1.0.1.0
		fix AddBAReq sequence
	
	PSK group TKIP msg2 problem, addAsicKey fail??
	

[V 0.0.1.d4]
[V 0.0.1.d3]
Shared-WEP: do not swap endian for Authen SEQ#3 for shared-wep
WPA2-PSK () - RTMPMakeRSNIE - have to do this in CntlOidRTBssidProc

[V 0.0.1.d2]
deadlock in MlmeHandler called by SetInfo
correct AID endian for PS mode
WPA2-PSK () - RTMPMakeRSNIE - have to do this in set OID_802_11_WEP_STATUS


[V 0.0.1.d1]

====================================================================================================
The base windows version
====================================================================================================
[V0.1.8.3]
1. BBP R69,R70,R73 has different value for rt2860D. So driver set different value for rt2860C/D.

[V0.1.8.2]
1. Before do scanning, set BBP R4 to 20MHz mode.
2. Let TX/RX PSDU max size limit as 16KB. (p.s : set {MAX_LEN_CFG,0x00001fff} /pAd->CommonCfg.HtCapability.HtCapParm.MaxRAmpduFactor = 1; respectively)

[V0.1.8.1]
1.change b/g protect mode ,frame gap to HT_TXOP
[V0.1.8.0]
1. release
2. Fix WiFi-dual band problems
3. Fix Adhoc problem in A band
4. Fix site survey issue when change country region
5. Fix RTS issue

[V0.1.7.0]
1. release

[V0.1.6.1]
1. Pass APSD, WMM, h+d in-house certification
2. Updat firmware v0.3, and support signal led mode
3. Fix surprise remove issue
4. Modify power save, the min current is about 24mA
5. Support legacy DLS protocol

[V0.1.6.0]
1. Improve Softap <-> Intel IOT 
2. Update some MAT register based on Jerry

[V0.1.5.6]
1. Update Led default value
2. Update WMM parameter
3. Fix check build crash issue

[V0.1.5.5]
1. Update some IOT in TGn plugfest#4.  (Stick to ShortGI(use #if WIFI_TEST), INTEL BA setup issue, MCS=32)

[V0.1.5.4]
1. Fix site survey in dual band because the scan time is too long
2. Support legacy WMM (haven't passed certification)
3. Support APSD (haven't passed certification)
4. Support 11h+d (haven't passed certification)
5. Fix driver freezed when Adhoc
6. Updat firmware v0.2, fix led issue.

[V0.1.5.3]
1. Solve IOT issue. Details in nIOT.doc.
2. PaulWu suggest spinklock in MiniportMMRequest

[V0.1.5.0]
1. Shift 802.11n OID definition that has conflict with WMM, Aggregation OID definition that was applied in rt61 after rt2860 driver coding.
2. V0.1.5.0 version driver should be used with new rt2860 GUI after 11/30.

[V0.1.4.0]
1. release

[V0.1.3.3]
1. Fix Tkip MIC fragment issue
2. Fix ZeroConfig/FunK UI with WPA2 security issue
3. Fix Adhoc Beacon Issue

[V0.1.3.2]
1. Fix fragment issue
2. Update the E2PROM reading routine for tx power per channel since we will support 40MHz in A band
3. Fix bug in auto wake routine
4. Update LED default value
5. Fix dual band issue in SoftAP
6. Update RF channel programming table to support 40MHz in A band
7. Fix Tx rate error when Adhoc with more than two clients
8. Check in firmware v0.1, this version is the first version which supports LED mode, power saving.

[V0.1.3.1]
1. Add Station connects to Pre-N only AP.
2. Rx EAP Fragment frames will fail on TKIP mode.
3. EAPOL frame will be encrypted while WPA_802_1X_PORT_SECURED.
4. Fix 2c_wlan_wep failed item.

[V0.1.3.0]
1. release

[V0.1.2.4]
1. fix surprise remove may cause infinite loop
2. fix WPA-None security issue.
3. fix counter measure issue.
4. fix DHCP frame checking on SoftAP mode.
5. fix wep encryption might fail cause by bTxkey floating.
6. fix WPA both mode security.
7. Retry to more times will cause WHQL testing failed on FailedCount checking.

[V0.1.2.3]
1. Fix adhoc basic rate in beacon
2. Fix basic rate bitmap in MAC register
3. Fix RSSI report error in UI site survey page
4. Support Hardware Radio on/off
5. Support TxPower percentage control
6. Fix TSSI read from E2PROM error
7. Fix bug, always 1Mbps when B mode

[V0.1.2.2]
1. Support RTS/CTS-to-Self
2. Fix countermeasure 
3. Fix country region issue

[V0.1.2.1]
1. Support dual band
2. Fix country region issue
3. Fix PHY issue between difference BW

[V0.1.2.0]
1. release
2. Fix some n negociation bug. [Jan - mlme.c]
3. Make initial N(Phymode) setting from registry correct. [Jan - init.c, info.c]
4. IOT with MBA more stable. (Marvel/Broadcom/Atheros) [Jan - data.c]

[V0.1.1.1]
1. NdisMIndicateStatus can't be called when driver is on halt progresss (ap.c)
2. Put WPA(#221) Element ID on the end of inside the association frame. (assoc.c)

[V0.1.1.0]
1. release

[V0.1.0.2]
1. Remove LinkDown Timer here. move it to properly place.
2. Used LinkUp Timer to indicate link up event.
3. Modify security relative codes
4. Use LinkDown Timer to indicate link down event after intiailize.
5. All security work.

[V0.1.0.1]
1. Fix MacTableInsertEntry will clear WEP Cipher if on station mode on ap.c
2. remove unnecessary code on connect.c
3. Modify RTMPAddBSSIDCipher for fixing WEP not work on rtmp.h & rtmp_info.c & sanity.c
4. Modify RTMPHandleInterrupt consider false interrupt cause by suprise remove on rtmp_man.c
5. Modify RTMPHalt on NIC exist or not in rtmp_main.c
---
6. Auto recognize Bad atheros chip , and turn on ASIC sending RTS register.
7. Add HTIOTCheck function for test, if not work, will delete in the future. 
8. IOT_STRUC structure is to store all InterOpbility action parameter.

[V0.1.0.0]
1. handle BAR control frame.
2. Periodically check BA reordering queue and refresh if possible.
3. Atheros IOT problem workaround.

[V0.0.9.4]
1. Fix countermeasure
2. Fix SoftAP WPAPSK/WPA2PSK
3. Update DRS algorithm to imporve throughput when open environment

[V0.0.9.3]
Release by Jan to fix atheros compatible issue, it should be checked in later.

[V0.0.9.2]
1. Fix Radio on/off issue, but not best power save
2. Fix NdisReset issue
3. Fix hibernate issue
4. Fix bug in RTMPMaxRssi 
5. Fix DRS issue

[V0.0.9.1]
1. Fix prefast build issue.
2. Support x64 platform
3. Rename .inf and .sys file name

[V0.0.9.0]
1. AP dynamic antenna status check
2. Modify calcuating rssi method according to Gain and RssiOffset in E2PROM
3. Modify load firmware routine about CRC check 
4. Update DRS function
5. Fix 20/40 MHz bandwidth issue

[V0.0.8.0]
[V0.0.7.1]
1. Change broadcast and mlme rate as CCK 1Mbps
2. Fix BA bugs
3. Dynamic antenna status check
4. Fix rssi report issue
5. Fix DHCP issue
6. Fix throughput issue caused by protection

[V0.0.7.0]
1. Basic MCS rate adaptation
2. MCS initial rate according RSSI
3. Update ASIC auto-fallback according to MCS table
4. Fix WindowsXP SoftAP bridge issue when AMSDU
5. Fix CCK fail issue becasue of BBP AGC
6. Update ethreal format to support rate, rssi
7. Update BBP, MAC, RF register initial value
8. Fix 20/40 MHz bandwidth issue

[V0.0.0.6]
1. RT2860c emulation ping ok


